You are not logged in.
- Topics: Active | Unanswered
Pages: 1
#1 2017-06-05 17:39:37
- Shahin
- Administrator
- Registered: 2016-02-17
- Posts: 3,546
SLS 3D Printers
We have plan to add SLS support to NanoDLP.
Is there anybody working on low cost SLS printer and want to collaborate with us?
Offline
#2 2017-06-23 17:54:31
- NeelD
- Member
- Registered: 2017-06-02
- Posts: 44
Re: SLS 3D Printers
Wanhao said they are working on it.
Offline
#3 2019-09-19 14:01:41
- alkg
- Member
- Registered: 2019-04-10
- Posts: 11
Re: SLS 3D Printers
Is it possible to control the laser using nanodlp? as in the photo
What does the laser mean in the photo, what is this function?Which laser is needed?
Last edited by alkg (2019-09-19 14:04:05)
Offline
#4 2019-09-21 15:08:24
- Shahin
- Administrator
- Registered: 2016-02-17
- Posts: 3,546
Re: SLS 3D Printers
Provide link to documentation of the pictured device. No idea what is this.
Offline
#5 2019-09-21 18:01:36
- alkg
- Member
- Registered: 2019-04-10
- Posts: 11
Re: SLS 3D Printers
This is controlled via the LPT port, using the G code . Apply for laser show
https://ru.aliexpress.com/item/32863575 … CmM5NDLNog
There is a ready-made solution but I don’t know if it works
https://ru.aliexpress.com/item/32973601 … 2e0e1xfxvj
Last edited by alkg (2019-09-21 18:02:48)
Offline
#6 2019-09-23 03:13:39
- Shahin
- Administrator
- Registered: 2016-02-17
- Posts: 3,546
Re: SLS 3D Printers
LPT is not supported maybe if it setupped in a way to behave exactly like Serial it would work on nanodlp.
Offline
#7 2019-09-24 10:09:03
- elshad66
- Member
- Registered: 2017-03-31
- Posts: 118
Re: SLS 3D Printers
forget ,,,,, build a printer on galvo, it's hemorrhoids
killed a lot of time and energy
забей,,,,, строить принтер на гальво , это геморрой
уйма сил и времени угрохал
https://www.youtube.com/watch?v=02jm43UE-vk
Last edited by elshad66 (2019-09-24 10:14:51)
Offline
#8 2019-11-11 23:25:48
- mgillan
- Member
- Registered: 2019-09-11
- Posts: 8
Re: SLS 3D Printers
Hi Shahin, is there existing support for SLA (laser-based)? I have just discovered that there is now a laser option as shown in alkg's photo above, not sure when that was added. If so, what kind of galvos can you control? Is there another thread that addresses this?
Offline
#9 2019-11-12 05:53:54
- Shahin
- Administrator
- Registered: 2016-02-17
- Posts: 3,546
Re: SLS 3D Printers
You need RAMPS. New option (8 months old) just generate per layer gcode to move galvo around in x,y axis to fill parts.
Offline
#10 2019-11-12 08:01:08
- alkg
- Member
- Registered: 2019-04-10
- Posts: 11
Re: SLS 3D Printers
You need RAMPS. New option (8 months old) just generate per layer gcode to move galvo around in x,y axis to fill parts.
RAMPS 1.6 Plus ?
Offline
Pages: 1