You are not logged in.
Hello to everybody,
I'm new to this forum and I just got our new "mUVe 3D DLP Pro+" for the school up and running. The printer is working but I get some errors displayed, later more.
BUILD 1209
1.)
First I have some issues with switching On/Off the projector ( ViewSonic PJD7720HD ) using an RS232 to USB adaptor. I tested everything I found on this forum as well on the manual from mUVe, but getting no signal.
I testet USB/Serial Port Address:
/dev/ttyACM0 - up to 4
and the same for
/dev/ttyUSB0 - up to 4
As I found the correct port it saved successfully under /dev/ttyUSB0 and also in the second test /dev/ttyUSB1
(but the printer board runs already under /dev/ttyUSB0 so I left it as /dev/ttyUSB1)
I also have the right On/Off settings, but when I press on the NanoDLP software the On switch, notting happens ?
Projector On: \x06\x14\x00\x04\x00\x34\x11\x00\x00\x5D
Projector Off: \x06\x14\x00\x04\x00\x34\x11\x01\x00\x5E
I attched:
Serial Terminal_ info after a print
Application Log Toggle Log
2.)
Which leads to my second problem.
If I press " starting print " it's showing me every 2 seconds
ActionSerial Communication Error EOF
ModuleSLAVE
3.)
The prints which coming out have always interrupted layers visible in the prints.
I tested all STL fliles and they are perfect water-tide and printing well on our other DLP system.
May this could come from the Error comunication problems, mentioned above ? Like slicing went wrong... ?
Or the stepper motor get wrong signal and missing steps ?
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
BUILD 1209
Application Log Toggle Log
Level Layer Time Module Details
Info undefined 2016-03-31 03:25:54.65126 Logging Suppressing duplicate logs
Error 1 2016-03-31 03:25:53.551295 SLAVE Serial Communication Error EOF
Error 1 2016-03-31 03:25:52.451175 SLAVE Serial Communication Error EOF
Error 1 2016-03-31 03:25:51.351206 SLAVE Serial Communication Error EOF
Warning 1 2016-03-31 03:25:50.251565 Terminal Problem Reading Terminal EOF
Error 1 2016-03-31 03:25:50.251311 SLAVE Serial Communication Error EOF
Info 1 2016-03-31 03:25:49.258664 Terminal Received Data From RAMPS: ok
Info 1 2016-03-31 03:25:49.258366 Terminal Received Data From RAMPS: ok
Warning 1 2016-03-31 03:25:48.231676 Terminal Problem Reading Terminal EOF
Error 1 2016-03-31 03:25:48.191328 SLAVE Serial Communication Error EOF
Info 1 2016-03-31 03:25:47.211151 Printing Job Completed
Debug 1 2016-03-31 03:25:47.211033 Pulsing Moving to Stop Position
Debug 361 2016-03-31 03:25:47.200539 Gcode Transfering Data M280 P2 S10
Debug 361 2016-03-31 03:25:47.199654 Shutter Shutter Close
Debug 361 2016-03-31 03:25:47.199475 Gcode Transfering Data
M84
Info 361 2016-03-31 03:25:47.19938 Gcode Position set to 41.1
Info 361 2016-03-31 03:25:47.199108 Terminal Received Data From RAMPS: Z_move_comp
Info 361 2016-03-31 03:25:47.196676 Terminal Received Data From RAMPS: ok
Info 361 2016-03-31 03:25:47.196346 Terminal Received Data From RAMPS: ok
Error 361 2016-03-31 03:25:46.211243 SLAVE Serial Communication Error EOF
Error 361 2016-03-31 03:25:45.111318 SLAVE Serial Communication Error EOF
Warning 361 2016-03-31 03:25:44.01149 Terminal Problem Reading Terminal EOF
Error 361 2016-03-31 03:25:44.011288 SLAVE Serial Communication Error EOF
Info 361 2016-03-31 03:25:43.034482 Gcode Waiting for done message from controller
Debug 361 2016-03-31 03:25:43.034265 Gcode Transfering Data M651
G1 Z41.1000
Info 361 2016-03-31 03:25:43.016096 Terminal Received Data From RAMPS: ok
Debug 361 2016-03-31 03:25:43.013366 Gcode Transfering Data M280 P2 S10
Debug 361 2016-03-31 03:25:43.012356 Shutter Shutter Close
Debug 361 2016-03-31 03:25:43.011739 Image Clear screen
Info undefined 2016-03-31 03:25:36.141251 Logging Suppressing duplicate logs
Error 361 2016-03-31 03:25:35.049185 SLAVE Serial Communication Error EOF
Error 361 2016-03-31 03:25:33.941107 SLAVE Serial Communication Error EOF
Error 361 2016-03-31 03:25:32.841067 SLAVE Serial Communication Error EOF
Warning 361 2016-03-31 03:25:31.741211 Terminal Problem Reading Terminal EOF
Error 361 2016-03-31 03:25:31.741123 SLAVE Serial Communication Error EOF
Debug 361 2016-03-31 03:25:30.761414 Printing Curing for 12.199999488 seconds
Info 361 2016-03-31 03:25:30.744833 Terminal Received Data From RAMPS: ok
Debug 361 2016-03-31 03:25:30.635562 Gcode Transfering Data M280 P2 S160
Debug 361 2016-03-31 03:25:30.634708 Shutter Shutter Open
Warning 361 2016-03-31 03:25:30.634069 Image Display layer public/plates/1/361.png
Warning 361 2016-03-31 03:25:30.63147 Terminal Problem Reading Terminal EOF
Error 361 2016-03-31 03:25:30.631286 SLAVE Serial Communication Error EOF
Info 361 2016-03-31 03:25:29.633708 Terminal Received Data From RAMPS: Z_move_comp
Info 361 2016-03-31 03:25:29.633618 Gcode Position set to 36.1
Info 361 2016-03-31 03:25:29.631397 Terminal Received Data From RAMPS: ok
Info 361 2016-03-31 03:25:29.631021 Terminal Received Data From RAMPS: ok
Info 361 2016-03-31 03:25:28.631614 Terminal Received Data From RAMPS: ok
Error 361 2016-03-31 03:25:27.671215 SLAVE Serial Communication Error EOF
Error 361 2016-03-31 03:25:26.571294 SLAVE Serial Communication Error EOF
Warning 361 2016-03-31 03:25:25.471453 Terminal Problem Reading Terminal EOF
Error 361 2016-03-31 03:25:25.471243 SLAVE Serial Communication Error EOF
Info 361 2016-03-31 03:25:24.471602 Terminal Received Data From RAMPS: ok
Info 361 2016-03-31 03:25:24.4674 Gcode Waiting for done message from controller
Debug 361 2016-03-31 03:25:24.467227 Gcode Transfering Data M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z36.1
Debug 361 2016-03-31 03:25:24.465139 Pulsing Moving to Layer
Info 360 2016-03-31 03:25:24.450263 Terminal Received Data From RAMPS: ok
Debug 360 2016-03-31 03:25:24.446812 Gcode Transfering Data M280 P2 S10
Debug 360 2016-03-31 03:25:24.445814 Shutter Shutter Close
Debug 360 2016-03-31 03:25:24.445395 Image Clear screen
Info undefined 2016-03-31 03:25:17.571219 Logging Suppressing duplicate logs
Error 360 2016-03-31 03:25:16.471288 SLAVE Serial Communication Error EOF
Error 360 2016-03-31 03:25:15.371129 SLAVE Serial Communication Error EOF
Error 360 2016-03-31 03:25:14.271146 SLAVE Serial Communication Error EOF
Warning 360 2016-03-31 03:25:13.175055 Terminal Problem Reading Terminal EOF
Error 360 2016-03-31 03:25:13.174804 SLAVE Serial Communication Error EOF
Debug 360 2016-03-31 03:25:12.194788 Printing Curing for 12.199999488 seconds
Info 360 2016-03-31 03:25:12.162013 Terminal Received Data From RAMPS: ok
Debug 360 2016-03-31 03:25:12.06621 Gcode Transfering Data M280 P2 S160
Debug 360 2016-03-31 03:25:12.065211 Shutter Shutter Open
Warning 360 2016-03-31 03:25:12.064684 Image Display layer public/plates/1/360.png
Warning 360 2016-03-31 03:25:12.061439 Terminal Problem Reading Terminal EOF
Error 360 2016-03-31 03:25:12.061254 SLAVE Serial Communication Error EOF
Info 360 2016-03-31 03:25:11.064271 Gcode Position set to 36
Info 360 2016-03-31 03:25:11.063127 Terminal Received Data From RAMPS: Z_move_comp
Info 360 2016-03-31 03:25:11.062713 Terminal Received Data From RAMPS: ok
Info 360 2016-03-31 03:25:11.062244 Terminal Received Data From RAMPS: ok
Warning 360 2016-03-31 03:25:10.961605 Terminal Problem Reading Terminal EOF
Error 360 2016-03-31 03:25:10.961371 SLAVE Serial Communication Error EOF
Info 360 2016-03-31 03:25:09.965285 Terminal Received Data From RAMPS: ok
Error 360 2016-03-31 03:25:09.001255 SLAVE Serial Communication Error EOF
Error 360 2016-03-31 03:25:07.901218 SLAVE Serial Communication Error EOF
Warning 360 2016-03-31 03:25:06.801506 Terminal Problem Reading Terminal EOF
Error 360 2016-03-31 03:25:06.801301 SLAVE Serial Communication Error EOF
Info 360 2016-03-31 03:25:05.804381 Terminal Received Data From RAMPS: ok
Info 360 2016-03-31 03:25:05.801302 Gcode Waiting for done message from controller
Debug 360 2016-03-31 03:25:05.801014 Gcode Transfering Data M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z36
Debug 360 2016-03-31 03:25:05.798544 Pulsing Moving to Layer
Info 359 2016-03-31 03:25:05.78282 Terminal Received Data From RAMPS: ok
Debug 359 2016-03-31 03:25:05.779962 Gcode Transfering Data M280 P2 S10
Debug 359 2016-03-31 03:25:05.779104 Shutter Shutter Close
Debug 359 2016-03-31 03:25:05.778742 Image Clear screen
Info undefined 2016-03-31 03:24:58.861222 Logging Suppressing duplicate logs
Error 359 2016-03-31 03:24:57.761298 SLAVE Serial Communication Error EOF
Error 359 2016-03-31 03:24:56.661215 SLAVE Serial Communication Error EOF
Error 359 2016-03-31 03:24:55.561275 SLAVE Serial Communication Error EOF
Warning 359 2016-03-31 03:24:54.461235 Terminal Problem Reading Terminal EOF
Error 359 2016-03-31 03:24:54.461128 SLAVE Serial Communication Error EOF
Debug 359 2016-03-31 03:24:53.528145 Printing Curing for 12.199999488 seconds
Info 359 2016-03-31 03:24:53.462484 Terminal Received Data From RAMPS: ok
Debug 359 2016-03-31 03:24:53.365487 Gcode Transfering Data M280 P2 S160
Debug 359 2016-03-31 03:24:53.364634 Shutter Shutter Open
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Serial Terminal info after a print:
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z33.3
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z33.4
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z33.5
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z33.6
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z33.7
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z33.8
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z33.9
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.1
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.2
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.3
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.4
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.5
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.6
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.7
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.8
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z34.9
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.1
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.2
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.3
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.4
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.5
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.6
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.7
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.8
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z35.9
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z36
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M650 D3.0000 S4.0000
M651
G4 P1000
G1 Z36.1
ok
ok
ok
ok
Z_move_comp
M280 P2 S160
ok
M280 P2 S10
ok
M651
G1 Z41.1000
ok
ok
Z_move_comp
M84
M280 P2 S10
ok
ok
4.)
NanoDLP telling me also = Connectivity problem Get http://www.nanodlp.com/build.muve3d.txt: dial tcp: lookup www.nanodlp.com on 192.168.2.1:53: read udp 192.168.2.100:59555->192.168.2.1:53: i/o
Es we have no internet right now, only slow modem... I hook it up with a wireless connecting between to PC (browser) and the PI only.
Could this cause trouble in print quality too ?
I appreciate any suggestion
Regards
Frank
Offline
Frank,
1,2,3 At-least for the part of log which you have pasted above. There is no visible effect of communication problem on the way your printer works. Every M / G commands received OK response from RAMPS so everything is fine.
Maybe errors reported by nanodlp all related to the projector communication. Disable it and see if the errors are persist or not.
If you have more than a one device using ttyUSB series address, due to a way linux works each time you restart system they could receive different address you need to fix this issue on rpi OS, there are loads of tutorial on this issue over the internet.
4. nanodlp checks for updates. It is fine if it fails to access internet.
Offline